Reliance

Whenever an alarm activation occurs on your system, all zones that were in alarm during that activation will be held in memory. The last alarm activation can be reviewed via the function listed below. i.e. You can see which area has activated the alarm.

1. Press [s] [3].
2. The ALARM MEMORY feature will flash those zones that created alarms and will light steady those zones that were bypassed during the last alarm.
3. Press [#] to exit.

TURNING THE DOOR CHIME ON AND OFF
The door chime is turned on or off by pressing the [CHIME] key while the system is in the disarmed state. If the chime is on, the chime light will be illuminated. If the chime is off, the chime light will be off. Each press of the [CHIME] key will toggle the chime feature on/off and produce a momentary ding-dong sound.

VIEW ALARM MEMORY

Step 1 Press the [p] key.

Step 2 Press the [3] key.

Step 3 The ALARM MEMORY feature will flash those zones that created alarms and will light steady those zones that were bypassed during the last alarm.

RESET SMOKE DETECTORS

This function is used to reset Smoke Detectors, Zone Troubles, and Zone Tampers.

Step 1 Disarm the system if not disarmed.

Step 2 Press the [p] key.

Step 3 Press the [7] key.

Reset has now been performed.

Step 4 If the code pad begins beeping, the reset did not execute properly. Enter your code to silence the code pad. Wait a few minutes and repeat step 2 to attempt another reset. If the code pad still beeps after repeated attempts,please contact your installer.

NOTE:You must hold these keys for 2 seconds to activate these functions. Your system may not be programmed for these activation keys (see page 1). You should press these keys only in an emergency situation that requires response by emergency personnel. If your system is programmed for these functions, the following reports can be sent.

Fire Key – This key can activate the fire alarm when pressed for two seconds.If your system is connected to a monitoring centre, an emergency report could be sent to that centre.

Auxiliary Emergency Key – This key can activate the auxiliary alarm when pressed for two seconds. If your system is connected to a monitoring centre,an emergency report could be sent to that centre.

Police (Panic/Hold-Up) Key – This key can sound a local audible alarm when pressed for two seconds. If your system is connected to a monitoring centre,an emergency report could be transmitted to that centre. NOTE: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring centre. Check with your installation company to determine how your security system will respond to the Panic/Hold-Up activation.

SET SYSTEM DATE

Step 1 Press the [*]-[9]-[6].

Step 2 Enter the “Master Code”.

Step 3 Enter the “Day of Week “

Step 4 Enter the “Month Code”. This must always be two (2) digits.

Step 5 Enter the “Day Code”. This must always be two (2) digits. Example: The 5th would be entered as [0]–[5].

Step 6 Enter the last two digits of the “Year Code”. Example: For 2000 enter [0]–[0].

SETTING THE SYSTEM CLOCK

Step 1 Press the [*] key.

Step 2 Press the [9]-[7] keys.

Step 3 Enter the “Master Code “.

Step 4 Enter the “hour code” which must be two (2) digits. Note: The clock is a 24hour clock.Example: 12.00 am would be entered as [0]-[0], 7.00 am would be entered as [0]-[7], and 5.00 pm would be entered as [1]-[7].

Step 5 Enter the “minutes code” which must be two (2) digits. Example: 7 minutes after would be entered [0] – [7].

TEST FUNCTION – Optional

If programmed, this function will perform a battery test, communicator test, and a siren test. No alarms will be sent, and no reports will be sent unless the communicator test is enabled.

Step 1 Press the [p] key.

Step 2 Press the [4]-[4] key. The test will be performed as programmed.

Step 3 If the siren test is performed, enter a user code to silence the siren.

No alarms will be sent and no reports will be sent unless a communicator test is performed, at which time a test signal will be sent.

WALK-TEST MODE –

Step 1 Press the [p] [Chime] key.

Step 2 Enter a “Master Arm/Disarm Code”. Now all zones become 24 hour, silent,and local (non-reporting zones). By faulting any zone, that zone will latch its zone light on the LED code pad, and sound the Chime. The Chime will continue to sound each time a zone is faulted. Once all zones are tested(zone lights lit on the LED code pad), go to Step 3.

Step 3 Press a “Master Arm/Disarm Code”.

SERVICE MENU

The service light will be “on” if the security system requires service. If the service light is“on”, press the [p] key followed by the [2] key to determine the service condition. One or more zone lights will illuminate indicating what service(s) is required. Call your service provider immediately for these problems. Below is a listing of what each light means in a service condition.

CODE PAD CONTROL TONES (BEEPS)

1 Beeps for all keypresses.

2 Sounds a continuous tone during the entry delay time.

3 Pulses when a day zone is violated while the system is disarmed.

4 Pulses when a fire zone has a trouble condition.

5 Beeps 3 times for trying to arm with the “Ready” light off, if “Force Arming” has not been selected.

6 Beeps for 1 second or emits a “ding-dong” sound for the “Chime” feature.

7 Beeps during an exit delay; beeps rapidly for the last 10 seconds of an exitdelay; and beeps 1 second at the end of the exit delay.

8 Pulses when the armed status changes and the AC power is off.

9 Pulses when the armed status changes and any zone(s) is bypassed.

10 Pulses when the armed status changes and a low battery is detected.

11 Pulses when the armed status changes and a tamper condition is detected. Beeps to indicate telephone line cut, if selected.

12 Pulses when one or more of the following conditions are detected: zone or box tamper, low battery, ac power fail, or expander trouble.

Entering a valid code will silence the code pad sounder when it is pulsing. Please contact your installer if a trouble condition exists.

CHANGING USER CODES

ASSIGNING USER CODE AUTHORITY LEVELS

Assign authority levels to users by following the steps below. Assign user codes before assigning authority levels.

Step 1 Press the [p][6] keys.

Step 2 Enter a “Master Arm/Disarm Code”.

NOTE: Someone changing the authority of another person can only add or remove authorization if they have access to that same authority level.

Step 3 The ready light will flash.

Step 4 Enter the 2 digit “user number” to be assigned authority (The ready light is constant and the partial light will flash).

Step 5 Lights illuminated indicate the authority levels assigned to this code. An explanation of the lights is listed below. You may toggle (turn on/off) the authority level by pressing the number for that authority level.

Step 6 Press the [p][p]. This returns you to Step 3. At this point you may enter another user number to assign authority level. Repeat Steps 4 – 6 until you have assigned authority levels to all user numbers.

Step 7 Press the [#] key to exit the Assigning Authority Level Program.